Adding Storage to MSA 2040
We are needing to add more drive space to our MSA 2040. Can someone point me in the right direction of performing this action. I'm new to the storage world. Any help is greatly appreciated. Thanks in...
View ArticleRe: Adding Storage to MSA 2040
Hello, Could you please answer me the follwoing > MSA 2040 SSF or LFF ?> Current capacity and enclosures ?> How much you are planning to upgrdade ? -JD
View ArticleRe: EVA 4400 (AG805C)
Thank you.....much appreciated i purchased 10 drives and all seems to be good still not sure of what license though but as i have downloaded demo version that comes with a temporary license which i...
View ArticleRe: EVA 4400 (AG805C)
much appreciated Jawad.............got it up and runningThank You Brian
View ArticleStorageWorks 4/8 SAN Switch Firmware Upgrade
Hello,I'm trying to do upgrade HP StorageWorks 4/8 SAN Switch to the latest firmware. Current version is 5.3.0d and the latest should be 6.2.x. I know that I cannot do direct upgrade to 6.2.x. I...
View ArticleRe: StorageWorks 4/8 SAN Switch Firmware Upgrade
ftp://ftp.hp.com/pub/softlib/software12/COL22074/co-86832-6/FOS-Drawer_Statement.htm Support and Usage Guidelines for OBSOLETED HP Switch Firmware Revisions v\:* {behavior:url(#default#VML);} o\:*...
View ArticleZoning issue
Hi! I am trying to connect a HP blade server (C7000) enclosure to a small SAN comprised of an EVA4000, 3 rx4640 servers (running HP-UX) and a tape library. This small SAN do not have zoning configured...
View ArticleRe: Zoning issue
I want to be able to run "ioscan -fnC tape" on the blade and see the tape library
View ArticleRe: Zoning issue
So you have the EVA, 2x stand alone switches, the servers, the blade servers (what model?) and blade switches, but no zoning.It is recommended to put disks and tapes in different zones, but without...
View ArticleRe: Zoning issue
Hi Please see the output of ioscan -fn:ioscan -fnC autoch prep03[138]/ #ioscan -fn Class I H/W Path Driver S/W State H/W Type Description...
View ArticleRe: Zoning issue
I can only see a netapp lun which is configured in a wrong mode and not redundant ...You did not tell about this device.More details needed. What switches are used between the devices? How is cabling...
View ArticleClik here to view.
Re: Zoning issue
this two IT rooms are separated by 100 m, and on the EVA side I did connect to one of the HP 4/16 SAN switchs and run the following:telnet 10.1.20.132 Trying... Connected to 10.1.20.132. Escape...
View ArticleRe: Zoning issue
Are there brocade switches in the C7000 too or something else (pass-tru for example)?
View ArticleClik here to view.
Re: Zoning issue
there are FC mezanine and pass-thru at the back of C7000, there is also connectivity from the back of C7000, to the brocade switch at the top.I was told by the Admin of the brocade switch of IT room 2...
View ArticleRe: Zoning issue
OK, if there is a zoning on the switch connected directly to the C7000, this may already block the blades from communication. I assume the single brocade next to the blade is connected to 1 brocade...
View ArticleRe: Zoning issue
Unfortunately I dont have access to the brocade switch next to the blade rack, but there is physical connectivity between the two, because of the rx4640 on the EVA side has file systems on the NetApp,...
View ArticleRe: Zoning issue
so the fcmsutil:fcmsutil /dev/fclp0 Vendor ID is = 0x10df Device ID is = 0xfe00 PCI Sub-system Vendor ID is = 0x103c PCI Sub-system ID is = 0x1708 Chip version = 2 Firmware Version = 2.72A2 SLI-3...
View Article