Re: Deleting EVA 8000 volumes from Solaris 10
Never used EVA on solaris but for iscsi volumes or dead scsi disk i use this commandThis will show all diskcfgadm -al This will remove the bad diskcfgadm -c unconfigure"dead removed"
View ArticleRe: HSV300 without management module
May be it will give a warning, but it will work without the module.
View ArticleMSA 2000i G1 Maximum Drive Size
Hello, due to "budget limitations" I've been tasked with determining if we can use 2 MSA 2000i that are currently using the 300 GB SAS drives (3 1/2"). I am tryting to find out what the maximum hard...
View ArticleEva4400: some beginner question
Please help if you can.My first SAN is coming at home today,i have connected contrller left1 to disck right2and controller right1 to disck left2,then i did the same with controller left2 to disck...
View ArticleRe: Eva4400: some beginner question
first problem solved: management control was a littly crooked
View ArticleRe: Eva4400: some beginner question
I have some errorsThe disk shelf is 04(mean no link?)the module say "unknown"i have connect as thisc1=controller c2=controller2 1=left 2=right d1=disk shelf1 d2=disk shel2...
View ArticleClik here to view.
Re: Eva4400: some beginner question
I have tried as manual said to connect DP1B with I/O BP2 and BP1A with I/O AP2I have this results"cell is in unknow state" from https module managementAnd two strange thing "04" on disk shelf and one...
View ArticleClik here to view.
Re: Eva4400: some beginner question
My module is similar to this,had a blinking amber on ! led ,mean total failure?No way to recover?
View ArticleClik here to view.
Re: Eva4400: some beginner question
The "04" is the number of the disk shelf, no error code. Are you able to connect to the management module? Is this a used array? Is it currently uninitialized (check from command view)? This is how you...
View ArticleRe: Eva4400: some beginner question
I make the cable correctly now,green green red red as your image saidThis is the answer of managemente module "his controller is inoperative because its FC loops or backplane mirror loops are...
View ArticleRe: Eva4400: some beginner question
This could be a hardware problem with either one of the controllers or the chassis itself. I would try to bring the array to life with a single controller first (CTRL1), the test with the other...
View ArticleRe: Eva4400: some beginner question
Very strange thing.I see different message for different browser(must be same for all browsers)
View ArticleClik here to view.
Clik here to view.
Re: Eva4400: some beginner question
First screenshot is the management module itself, second is command view. Both have same IP, but different ports.
View ArticleRe: Eva4400: some beginner question
Tried with one controller,give me controller in "attention state" and no wwn
View ArticleClik here to view.
Re: Eva4400: some beginner question
I have replaced dimm on controller2,now give another error Detailed System Information System Configuration Name: Unknown Initialization: Unknown World Wide Name: 0000-0000-0000-0000...
View ArticleRe: Eva4400: some beginner question
Returning to cabling,i hope to did it correctlyport are connected like thisC1=controller i/o hsv300 1 C2=controller i/o hsv300 2port1=aport2=bD1=disk shelf i/o1 D2=disk shelf...
View ArticleRe: Eva4400: some beginner question
Those are logsController1 TE 31.(1f) - Revisions MIST Complete. Completion Status: Multiple Error First Failed TE: 26.(1a) Test: 0.(00) Error Code: 1a000622 Completion Status: Fault Toler ant Hard...
View Article