Re: disk uncompatible on EVA6300
Unfortunately as i earlier mentioned,there is no seperate tool to set the EVA bit on the Hard drive and it is a factory setting.Please contact the Account support manager or contact support for further...
View ArticleRe: EVA 4400 managment module problem ?
All the troubleshooting steps have been already performed as mentioned in the post.Try to remove and reinsert ensure the laptop IP is in the same range of the management module IP and allow 15...
View ArticleEVA 8100 does not see hosts
Turned off the EVA 8100. After turning on the EVA 8100, the servers do not see the drives.And when the port is deleted, the controller reboots and leaves for an error.How can I extract data?Sometimes...
View ArticleRe: EVA 8100 does not see hosts
There could be some device in the loop causing the issue or the controller itself would be defective.Check the LED status on the controllers and loop switches.Reseat any loop switches or IO modules...
View ArticleRe: EVA 8100 does not see hosts
Checked all the loops. All indicators approx. rebooted the system. Disks on hosts are also not visible.Can I connect to the controller directly?
View ArticleRe: EVA 8100 does not see hosts
A serial cable designated to this array model needs to be connetced and collect the boot log.As mentioned earlier an indepth analysis of serial log is required to identify the issue.Hence i would...
View ArticleResetting EVA4400 Management Module not working
Hi All,As these things tend to do periodically, I lost connection to the EVA4400 management module. This time I tried resetting it, pulling it out, re-inserting it...nothing is working and I can't...
View ArticleRe: Resetting EVA4400 Management Module not working
Never mind...problem solved. When connecting with the laptop I had failed to configure the laptop with the same IP range as the management module. Once I did that, I was able to log in, set the network...
View ArticleRe: E-Port(segmented, incompatible)
SOme time you can also try portcfgislmode X 1.. make sure its ON
View ArticleEVA 8400 Disk Group Hardware Failure
Hi,We've got a very old EVA8400 which has one of it's disk groups in a state due to multiple disk failures. From what I can tell:We had a disk failure replaced yesterday during the day, so the disk...
View ArticleRe: Start Lun Failure
Did this ever get resolved? If so, was it an adapter setting, SAN fabric issue, or did you replace the FCA?
View ArticleHPE P6000 Control Panel
Доброго времени суток. Закрылась 2я компания, от нее достались 4 комплекта контроллеров с полками.К моей глупости и по незнанию, сделал сброс контроллера. позже выяснил что теперь у меня нет лицензии...
View ArticleRe: HPE P6000 Control Panel
Hello,The Command View license is generated by the system serial number and the user contract agreement. Since you have bought the system from a company you will have to purchase a new...
View Articlehow to work with "aliadd" command in san switch
how to work with "aliadd" command in san switch
View ArticleRe: how to work with "aliadd" command in san switch
The below link shoudl be useful.NOTE: Based on the SAN switch FOS version,you could download the FOS command reference guide.http://h20628.www2.hp.com/km-ext/kmcsdirect/emr_na-c04888474-1.pdfaliAddAdds...
View ArticleP6500 Storage problem
Hii am facing problem at My storage system P6500i found that error on controllerCompletion Status: Soft Error%Offload power supply failure%Failed TE: 28.(1c) Test: 9.(09) Error Code: 1c090ff0 BUD...
View ArticleRe: P6300 License Alerts
Did you find any solution?I have the same problem except it says my instant on license was expired on March 1970! Please help if anyone knows the solution. Hpe asking SAID which I dont have, but I...
View ArticleDisk EVA Storage not detect after replace Fail SAN Switch
Dear AllWe have problem when replace new SAN Switch, the disk use EVA Storage not detect. We replace SAN Swtich because older san switch fail.Is right, the solution only with vgexport/vgimport? can we...
View ArticleRe: Disk EVA Storage not detect after replace Fail SAN Switch
Yes, vgexport exports the definition only.Can you find it by doing a vgscan in preview mode?Did you create a proper zoning in the new switch?
View ArticleRe: Disk EVA Storage not detect after replace Fail SAN Switch
So, vgexport/vgimport in this case just exp/imp definition? not the data?vgscan :# vgscan -vvgscan: Warning: couldn't query physical volume "/dev/dsk/c4t0d1":The specified path does not correspond to...
View Article