Re: Download Command View 10.3.3 (ABM) and 10.3.4 (SBM)
ABM = array based management (command view for the built-in management module)SBM = server based management (command view for windows)
View ArticleEVA4400 Unpopulate Disk
I have EVA4400 with Firmware 11200000. Last time i change a failed hard disk. I add the disk in Disk Group but few hours later in Command View ( Installed in Windows Server ) i saw the disk as...
View ArticleEVA4400 MPIO for IBM AIX 7.1
i 'm trying to assign vdisk on eva4400 to IBM AIX 7.1 OS. On AIX, after run cfgmgr command, i see two disk with the same pvids and cannot create volume group for this disk.In EVA4400 installation...
View ArticleNumber of disks that can break
HelowI have aP4400EVAwith48disks configuredinto 1diskgroup,the question is,how many diskscan be broken withoutproblemsThank you
View ArticleRe: Number of disks that can break
"how many recordscan be broken without problems"? None. Data corruption is bad.Did you mean physical disk drives? In that case, if you are using RAID1 or RAID5, one disk. If you are using all RAID6,...
View ArticleRe: Number of disks that can break
I have one disk group configured with 48 disks and in the Disk Group, I have several Virtual disk that are RAID 1 or RAID 5 .
View ArticleRe: Number of disks that can break
Contact HPE EVA Support.Have them help you figure out what is wrong.If any RAID set is broken (not just degraded due to loss of a drive), the array will stop all IO to the affected virtual disks.
View ArticleRe: Number of disks that can break
If a disk fails, the array will re-organize to get fully redundant again. Same if the next disk fails after this reconstruction. This works as long as you have enough free space.
View ArticleRe: Eva4400: some beginner question
The solution was: bad cables. I have reorder all cables(all short parts n° 432375-001 and HP 509506-001 )And is work perfect: accept the WUID ,disk okThank you for help
View ArticleRe: Eva4400: some beginner question
Yes was wrongI had ordered 4 cables on ebay,one 0k...and three faults!So i re-ordered new cables from other people(uk,usa)and no problems.Works perfect
View ArticleRe: Eva4400: some beginner question
Simple question now: i have one port connected to server,and three free ports,is possible to shutdown them?They give me error,because connected to nothing
View ArticleQuestion about shutdown of hp4400
Simple and fast questionIf i want to shutdown the 4400 is correct to shutdownfirst server(hpux)then controller hsv300then disk shelf?Or is first disk shelf and then controller?
View ArticleDisk presentation: a little confuse
The port wwid(port of controller) and port wwid(port of the hb card on hpux server)are different,when i present disk i have to use hb card port wwid?Or port of controller?
View ArticleRe: Disk presentation: a little confuse
Ok solved,first of all if battery is exsausted my SAN doesn't workSo i put disk on controller2(battery ok) create failvover policyand use tdutil /dev/td0 to discover the correct portwich is "...
View ArticleRe: Question about shutdown of hp4400
Hiif you power down the EVA4400 from command view it shuts down the controller and then the disk enclosures by it self you must remember that the power switch is still onRegardsGive a Kudo if this helps
View ArticleRe: Question about shutdown of hp4400
I try to shutdown controller,controller shutdown okbut disk shelf remain on.
View ArticleRe: Question about shutdown of hp4400
Hiyou need to power down the EVA from command view this powers down the controllers and the disk enclosuresRegards
View Article