Re: EVA cabling (hardware configuration guide)
>The link is dead Rob, It "worked" fine for me. :-)I got your "We are sorry" message then a popup of switching to "HP Support Center - Hewlett Packard Enterprise" and I clicked and it was right...
View ArticleWWPN is not reflecting in SAN switch
Hi All, Please help me in the below issue. After configuring Server profile in VCEM, the server WWPNs are not reflecting in SAN switches where the chassis has been connected. (This issue is not always...
View ArticleRe: EVA 4400 - remote console unavaiable
Hi Amiga,I think it is not a serious problem.Restart the service of CV in windows services and then connect to the URL.
View ArticleHP EVA 4400 disk replaced now states Object not found. Operation on this...
We had a disk failure in our HP EVA 4400. The disk was replaced which put the new disk in the ungrouped container however when you click on the disk it says "Object not found. Operation on this object...
View Articlecommand view not seeing EVA 4100
had a working cv 7.0 on server 2k3 and eva xcs 6.110. needed to upgrade pc running CV to 2012r2. upgraded the HSV200 to 6.220 using HSV200_6220.sss and installed cv 10.2. When I start CV 10 it will...
View ArticleRe: command view not seeing EVA 4100
XCS 6250 and CV 10-3-6 would be the better combination. Did you look into "unmanaged systems" in CV? Your EVA should be there.
View ArticleRe: command view not seeing EVA 4100
Since I have a non-hp support contract I am not sure where to find the XCS 6.250 downloads. The split up of HP's support sites august 1st, makes it harder to find updates as well since the majority of...
View ArticleRe: HP EVA 4400 disk replaced now states Object not found. Operation on this...
Restarting my CV server solved the issue.
View ArticleWindows Server 2012 X64 host mode on XP24000
I am preparing to present LUNs to a Windows Server 2012 host and not sure if I should use 0C or 2C for the host mode in XP24000 Remote Web Console LUN Manager. Which mode would be most correct ?
View ArticleEva4400 showing 0gb of available space
I have an eva440 that is showing 0gb of available space for any type of vraid even though it is only about 50% allocated. I have restarted the command view server and no change. Also, restarted the...
View ArticleHp eva4400 controllers hangs
Hello,we have an HP EVA4400 which caused a sudden stop of all connections to servers and command view no longer sees the strorage .after having power off the controller mapping returns slowly. this...
View ArticleEVA 4400 firmware upgrade question
Have an eva 4400 running 10001000 firmware. Had a disk go bad and support suggested upgrading to11300000. Our eva is connected to a c7000 blade chasis, blades running vmware. My question is...
View Articlecascade 2 HP Power Pack FC SAN Switch
Dear All,i have 2 FC san switch i need to be cascaded.first switch is configure by zone and fos:7.0.0c model HP 8/24 Power Pack FC SAN Switchsecond switch is not configure yet and fos:6.2.0d model HP...
View ArticleRe: cascade 2 HP Power Pack FC SAN Switch
A better plan is to update your switch firmware. Both of them. A quick check at HP Storage SPOCK (Single Point of Connectivity Knowledge for HP Storage Products) http://www.hp.com/storage/spock shows...
View ArticleRe: Hp eva4400 controllers hangs
hi, someone who can draws some things from these logs !! thanks
View ArticleRe: Hp eva4400 controllers hangs
Did you replace some disks recently?They look like failed. Encl. 3 bay 1Encl. 3 bay 8Encl. 7 bay 4 By the way, firmware XCS 09534000 is not supported since early 2014. You should consider to update to...
View ArticleRe: Hp eva4400 controllers hangs
Hi, thanks Torsten for your reply i well verify and let you know. thanks
View ArticleRe: MPX110 FC ports not working Loopback->Port 5
We are facing the same issue have you resolved the FC port?
View ArticleRe: Command View - Login not possible
Just below thing will resolve this issue Execute the following command on the server or management module where you are installing HPCommand View EVA:cd C:\Program...
View Article